Memfilter AHC - Active Harmonic Conditioner

Harmonic distortion caused by non-linear electrical loads is becoming a growing problem for both electrical suppliers and users. The ever increasing use of computers, variable speed drives, UPS systems and switched mode power supplies is causing excessive heating in transformers, switchgear and cables and damage to sensitive electronic loads.

Various techniques have been employed to overcome this problem.
These include:

  • Derating transformers and switchgear, or oversizing cables
  • Using special phase shift or isolation transformers
  • Inserting series reactors
  • Using tuned passive filters

There are arguments for and against each of these solutions but, whichever system is chosen, it is either difficult to install or totally inflexible to the changing needs of a modern day system.

The more flexible approach is to use the Memfilter AHC.


 Contact Details


TopHome

 

The Memfilter AHC

The Memfilter AHC is an active harmonic conditioner which counteracts the harmonics by injecting equal and opposite signals into the supply to cancel the offending waveforms.

Using state of the art technologies the Memfilter AHC can compensate for harmonics ranging from 2nd to 25th and gives the user the choice of either global or pre-selected order compensation.

Units can be used on three phase networks to give automatic compensation for either three phase, or single phase, harmonic distortion.

Memfilter AHC has the following advantages over all other forms of harmonic control:

  • It continues to guarantee efficient harmonic compensation even when changes are made to the installation
  • It is easy to use and install
  • It auto configures to harmonic loads whatever their magnitude
  • It is not susceptible to harmonic overload
  • It is compatible with electrical generators
  • It can be connected to any point in the network
  • Additional units can be added to meet future system requirements






Low voltage diagram showing the possible connection points for the Memfilter AHC depending on the compensation level required.

 Contact Details


TopHome

 

Memfilter AHC Installation

Memfilter AHC is easy to install either on a wall or within a switchboard. It requires either a three or four wire supply to the unit and the insertion of the measurement sensors into the polluted power supply.

If the objective is to reduce distortion on the supply authorities network then the unit needs to be placed upstream of the polluting load with the injection point as near to the point of incoming supply as possible.

If the need is to reduce pollution within the installation the unit must be positioned upstream but next to the pollutant.

We can carry out an accurate harmonic pollution audit and then develop a flexible, high performance solution with guaranteed results.


 Contact Details


TopHome

 

Memfilter AHC Specification

Model

SW20

SW30

SW45

SW60

SW90

SW120

Technical
Specifications
           

Phase Compensation
Capacity (A rms)

20

30

45

60

90

120

Neutral Compensation
Capacity (A rms)

60

90

135

180

270

360

Nominal Voltage

400V <15%> standard,
208, 220 or 480V on request

Nominal Frequency

50Hz, 60Hz <8%>

Number of Phases

3 phases with or without neutral -
operation is possible on unbalanced or
single phase loads

Current Transformers

Ratings from 300/1 to 4000/1 available

Harmonic Current
Compensated

Orders 2 to 25, global compensation
or specified harmonics

Rate of Harmonic
Reduction

THDI load/THDI network > 10
at normal capacity of unit

Current Compensation
of Cos ø

Up to 1.0

Response Time

<40 ms

Overload

Limited to continuous operation
at normal current

Inrush Current

< twice nominal peak current

Losses

1000W

1300W

2100W

2600W

4200W

5200W

Noise Level
- less than

55dBA

55dBA

60dBA

60dBA

65dBA

65dBA

Colour

RAL 9002

Dimensions
           

Height (mm)

680

680

780

780

780

780

Width (mm)

540

540

590

590

590

590

Depth (mm)

280

280

325

325

325

325

Weight (mm)

65

65

110

110

220

220

Environmental
Conditions
           

Operating
Temperature

0 to 40°C continuous,
<25°C recommended

Relative Humidity

0 to 95% non condensing

Operating
Altitude

<1000m

Reference Standards
           

Construction and
Safety

EN 50091-1

Design

IEC 146

Protection to
IEC 529

IP30

Electromagnetic
Compatibility
           

Conducted and
Radiated Emission

EN 55011 Class A

Immunity to
Electrostatic
Discharges

IEC 1000 - 4 - 2 level 3

Immunity to
Electromagnetic
Fields

IEC 1000 - 4 - 3 level 3

Immunity to
Impulse Waves

IEC 1000 - 4 - 4 and
IEC 1000 - 4 - 5 level 4

Larger loads can be accommodated,
we will be pleased to discuss your individual requirements.

 Contact Details


TopHome

 



Quotations Telephone:

08700 507 545 (option 1)

Quotations Facsimile:

08700 507 520
 E-mail: Quotations

Orders & Projects Telephone:

08700 507 545 (option 2 or 3)

Orders & Projects Facsimile:

08700 857 603
 E-mail: Orders & Projects

Address:

Eaton MEM, Reddings Lane,
Birmingham B11 3EZ - United Kingdom
 UK Sales Contacts & Distributors
 Eaton MEM Worldwide

TopHome


© Copyright Eaton Electric Ltd.